Plastic Shower

Plastic Shower
Plastic Shower

How an installment Shower Drain

Plumbing a shower drain for your new home is a short and simple process. Although it requires attention details, you can install a shower drain you a professional with a bit of planning and some common construction tools.

Map your drain hole. To determine the location, set the floor pan for your shower in the frame you have built. Ensure that you have a shower pan facing the right way, and then use a pencil to mark the location of the drain under the frame.

Exit the shower pan out of the frame and cut a drain hole in Your Sword or reciprocating saw. The hole should be a bit wider than the drain opening your shower pan, about 6 inches in diameter. If you are setting a shower directly into a concrete floor, you will need to run the plumbing for the drain through a gap in the concrete and the ground with a PVC ground joint adapter.

Still in the shower pan out, insert drain the potatoes, the portion of the drain screws on the pan. Using nut potatoes, thread the drain potatoes in pan shower. A potato wrench is the best tool for threading nuts potatoes. Be nice to the drain potatoes. This thread until it feels snugly attached, do not overtighten it.

Set the drain pan. To complete the installation of your gutters, you will need to yet plumbed a trap-P, a type of plumbing fixture often used in the sink, bathtub and shower drains. Depending on the length, you will probably also need a 2 inch PVC riser in diameter to bring the height up to reach your shower drain. By Rick Peters in "Home How-To Handbook: Plumbing," most manufacturers recommend shower strip handle water-level wet set plaster, mortar or non-expanding foam.

After your shower pan is set and leveled, use a rubber gasket seal stable the gap between your PVC shower riser and potatoes. The best way to dump a gasket in the area was tender to hammer them with a packing iron or flat piece of metal. You should use lubrication to get the gasket in place. If you are using a plastic shower, you might need to cement your riser pipe right into the shower Instead of inserting a gasket.

Set the shower drain guard in place over the shower drain. Some require that you shower drains or pop the screw it, while others just rest inside the drain hole.

If you can not access the plumbing under the shower drain to form a tight seal, you may need to use a compression-type connector.If you can not access the plumbing under the shower to form a tight seal, you may need to use a compression-type connector.

About the Author

xlnb.cn is a Manufacturer and suppliers of shower drain, sheet metal stamping, metal stamping, Equipment parts by OEM/ODM service with diversified schemes.

Bathroom Cleaning Tips : How to Clean Plastic or Vinyl Shower Curtains

No items matching your keywords were found.



Shower Rod Cover by Jenacor | Rod Cover Rod Covers Plastic Tubing Rod Protective Cover Rod Cover Sleeve | Black Plastic Shower Rod Cover 1 inch diameter x 59 inches long 2-Pack


Shower Rod Cover by Jenacor | Rod Cover Rod Covers Plastic Tubing Rod Protective Cover Rod Cover Sleeve | Black Plastic Shower Rod Cover 1 inch diameter x 59 inches long 2-Pack


$19.95


Renew your shower in a flash. Finally there's a quick, easy way to make your shower feel brand new: simply cover your banged up old shower rods with a silky black shower rod cover from Jenacor. Made of durable pvc tubing, each is precisely measured to fit a standard 1 inch diameter shower rod and is a full 59 inches long. Just cut the rod cover to measure with any household scissors, then snap it ...

Eforgift Water Repellent Stall Shower Curtain Liner Mold Resist with Magnetic Bottom and Metal Grommets, Plastic Shower Curtain Liner Non-PVC, 54 inches x 78 inches


Eforgift Water Repellent Stall Shower Curtain Liner Mold Resist with Magnetic Bottom and Metal Grommets, Plastic Shower Curtain Liner Non-PVC, 54 inches x 78 inches


$13.99


Pattern: Transparent Color: Clear Material: 100% Eco-friendly PEVA Package included: 1x shower curtain / sets of 12 plastic curtain rings Product Features: 100% PEVA, Non-toxic, Anti-bacterial; Soft touch, Fade/Stain Resistant, Durable; 2 magnets to keep the liner in place; With rustproof metal grommets and plastic curtain rings; Can be folded, no wrinkles; Could used as shower curtain alon...

mDesign PEVA 3G Shower Curtain Liner (PACK of 2), Eco Friendly, MOLD & MILDEW Resistant, ODORLESS - No Chemical Smell, 72 x 72 - Frost


mDesign PEVA 3G Shower Curtain Liner (PACK of 2), Eco Friendly, MOLD & MILDEW Resistant, ODORLESS - No Chemical Smell, 72 x 72 - Frost


$9.99


Our mDesign basic shower curtain liner is water repellent, odorless, mold/mildew resistant, and even has magnets at the bottom hem to provide weight and stability to keep the shower liner in place....

Maytex Heavy Duty Plastic Roller Glide Shower Rings, Clear


Maytex Heavy Duty Plastic Roller Glide Shower Rings, Clear


$2.97


Maytex plastic glide roller shower rings is durable, easy to use, and easy to clean. Made of durable 100-percent abs plastic. Sold in sets of 12. Check out all the Maytex shower rings and hooks....

Premium Plastic Shower Rings in Clear


Premium Plastic Shower Rings in Clear


$5.99


These clear plastic shower curtain rings fit around standard 1" and 1.25" shower rods and through standard-sized shower liner grommets. Made of BPA-free plastic. Clean with a damp cloth....


Leave a Reply

  

  

  

You can use these HTML tags

<a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>